|

One Leak in Unit C Shut Off Water to All Four Units

The text came in from the tenant in Unit C at 6:40 on a Sunday morning. It was a photo of the laundry closet. A thin spray was coming out of the wall above the washer box, fanning across the dryer and onto the floor. The caption said, “Is this normal?”

It was not normal. The owner drove over in sweatpants. She found the main shutoff by the sidewalk, turned it, and stood there while the spray died down to a drip.

Then her phone started buzzing again. Unit A had no water. Unit B had no water. Unit D, upstairs in the back, had a houseguest in the shower with shampoo in her hair.

That is the fourplex problem in one morning. One leak, in one unit, and four households lose water at the same valve.

The building was a 1958 fourplex in Santa Clara. Two units up, two down. Her father bought it in the seventies and ran it out of a shoebox of receipts. She inherited the shoebox, the building, and the original galvanized steel water pipe.

Repipe Champions does water-supply repipes in Bay Area houses and small multi-family buildings. CSLB #1057926. This post is about what she decided after that Sunday, and how you repipe a building with people living in it.

The short version, if you stop reading here

When one unit in a small building springs a leak on old supply pipe, the owner is usually choosing among three answers.

  • Fix the leak and wait. A plumber cuts out the bad section and puts in a new piece. Fits when the rest of the pipe is in decent shape and this was a one-off. Does not fit when the pipe is the same age and material everywhere, and this is the second or third leak.
  • Repipe the one unit. New supply lines inside the unit that leaked, tied back to the old pipe that feeds it. Fits when that unit was plumbed differently, or was remodeled with different pipe. Does not fit when the old pipe that feeds all four units is the real problem.
  • Repipe the building. New main, new branches to each unit, new lines inside each unit, new shutoffs. Fits when the whole building is on the same old pipe and you want to stop getting texts at 6:40 on Sunday. Does not fit when you need a one-day answer and the budget is not there yet.

All three get better with the same first step. Somebody who repipes buildings walks the whole thing. Every unit, the main, the crawlspace or the attic, and every water heater closet. Then you are choosing between written scopes, not between guesses.

Why one leak shut off four kitchens

A lot of small Bay Area apartment buildings from the fifties and sixties were plumbed like one big house. One water meter. One main line from the meter to the building. Then the pipe splits and runs to each unit.

Back then, nobody thought much about shutting off one unit at a time. A building like this might have a valve for each water heater and maybe a stop under each sink. That is it. When something breaks in a wall, there is often no valve between that wall and the street.

So the owner in Santa Clara had one real choice at 6:45 that morning. Turn off the whole building, or let Unit C’s laundry closet keep filling. She made the right call. Three other households paid for it.

This is the part of a building repipe that owners notice later. A good repipe puts in a shutoff for each unit. Next time a toilet supply line lets go in Unit B, Unit B turns off. Everybody else keeps making coffee.

What the plumber found behind the washer

The plumber who came out that afternoon opened the wall behind the washer box. The pipe was galvanized steel, gray on the outside, orange at the threads. The leak was a pinhole on the bottom of a horizontal run, a few inches from a fitting.

He cut out about two feet and put in a new piece. The building got its water back by early evening. He also said the thing service plumbers say a lot in buildings like this. “I fixed this spot. I can’t tell you about the next spot.”

He was being honest. Here is why.

Galvanized steel is steel with a zinc coating. The zinc wears away from the inside over the decades. Then the steel underneath rusts. Rust and minerals build up on the inside wall of the pipe and the opening gets smaller. Where the wall gets thin, usually at a thread or along the bottom of a run, it eventually goes through.

Every unit in that building was on pipe from the same year, from the same supplier, carrying the same water. The pinhole in Unit C was not a freak. It was the first one to show up.

The tenants had been telling her for a while

After the Sunday leak, the owner did something smart. She went back through two years of texts and emails from the tenants and searched for “water.”

Unit A had mentioned that the shower went cold when someone ran the kitchen sink. Unit B had asked twice about brownish water in the bathtub after they came back from a trip. Unit D, the upstairs back unit, had said the water pressure was “kind of weak” and asked if there was a filter somewhere that needed changing.

None of those messages sounded like an emergency. Each one got a polite answer and a “let me know if it gets worse.” Read together, in a row, they told the same story as the pinhole.

  • Pressure drops when two fixtures run. The pipe is narrowing inside. One faucet can look fine. Two fighting over the same narrow line is where it shows.
  • Brown water after it sits. Rust coming off the inside of the pipe. It is usually worst first thing in the morning or after a vacation.
  • Weak pressure upstairs. The upstairs units are at the end of the longest, highest run. They feel a narrowing pipe first.

Tenants are good leak detectors. They use the water every day and they notice when something changes. They just do not usually phrase it as “I believe your galvanized supply is scaling shut.”

Three ways to answer the next leak

The owner called us after the second plumber visit, which came eleven days after the first. Same building. Unit A this time, under the kitchen sink. Different pipe, same age.

We walked the whole building with her. Here is how the choices looked once we could see all four units.

Keep patching

When it fits: the pipe is mostly sound and the leaks are rare. Some buildings have one bad section, from an old repair or a run that sat in a damp spot.

When it does not: the leaks are coming from different units on pipe of the same age. That was this building. Each patch fixes a few inches of pipe and leaves the rest exactly as old as it was.

Patching also has a cost people forget. Every leak is a tenant phone call, a wet floor, a shutoff for the whole building, and an afternoon of somebody’s life. In a single-family house, that is the owner’s own afternoon. In a fourplex, it is four households’ afternoons, and one of them is always the one with the houseguest.

Repipe one unit at a time, over time

When it fits: one unit was plumbed differently, or has had worse luck, and the main that feeds the building is in decent shape. Some owners also do a unit at a time on turnover, when a unit is empty between tenants.

When it does not: the pipe that feeds all four units is the same old galvanized. Putting new pipe inside a unit does not fix what comes up to it. The upstairs tenant will still have weak pressure if the narrowing is in the line that climbs to the second floor.

Turnover repipes can still make sense as part of a bigger plan. But a plan of “whoever moves out next” can take years in a building where good tenants stay put. This building had one tenant who had been there since before the owner’s father retired.

Repipe the building

When it fits: the whole building is on the same old pipe, you are getting leaks in more than one place, and you want one project with one permit instead of a string of emergencies.

When it does not: you need the work done in a single day, or the budget is not there this year. A building repipe is a real project. It deserves a written scope and a schedule, not a rushed yes.

The owner in Santa Clara chose the building. Her reasoning was simple. “I’m going to pay for this pipe either way. I’d rather pay for it once.”

Living in the building while the pipe gets replaced

This is the question owners ask first, and it is the one that scares them the most. Do the tenants have to move out?

Usually, no. A repipe in an occupied building is very common. The crew opens small sections of wall and ceiling where the new pipe needs to run, pulls the new lines, connects them to each fixture, and patches the openings. Furniture gets moved away from the work areas. Floors get covered.

The difference between a smooth occupied repipe and a miserable one is mostly planning. A few things matter more than anything else.

Notice comes first

Tenants have a right to know when someone is coming into their unit. California’s rule for landlord entry is in Civil Code section 1954. In plain English, a landlord can enter to make necessary repairs, generally during normal business hours, after giving reasonable written notice. The statute presumes 24 hours is reasonable notice. If the notice is mailed, it presumes six days before the entry is reasonable.

That is the floor, not the ceiling. On a building repipe, the best owners send a short letter well ahead of the work that explains what is happening and why, and then the 24-hour notices on top of it, unit by unit.

The owner in Santa Clara wrote a one-page letter. What the work is. Why. Which days crews would be in which unit. Which days the water would be off during working hours. Who to call with questions. Her phone number was on it. So was ours.

If you have a property manager, they likely already have a notice form they trust. If you have questions about notice rules for your specific situation, ask your property manager or a landlord-tenant attorney. We are plumbers. We will tell you what the work needs. They will tell you what the paperwork needs.

Water off by day, back on by night

California’s habitability rule, Civil Code section 1941.1, lists the basics a rental has to have. One of them is a water supply that produces hot and cold running water, furnished to appropriate fixtures. Another is plumbing kept in good working order.

That is part of why repiping is worth doing. It is also why the schedule matters. On an occupied building, the goal is short daytime shutoffs and water back on in the evening, so people can cook dinner, wash up, and shower.

When you get a scope for a building, ask for the shutoff plan in writing. Which days the water will be off. Roughly which hours. Whether the whole building goes off or one unit at a time. A crew that has done this before will have an answer. A crew that says “we’ll figure it out” is telling you something.

One unit’s bad day should not be everyone’s bad day

The first thing a building repipe usually does is fix the problem from that Sunday morning. New main, new branch lines, and a shutoff for each unit where it makes sense. Once those are in, a lot of the remaining work can happen one unit at a time while the other units keep water.

The tenants in Santa Clara noticed this before they noticed anything else. Partway through the job, the upstairs back tenant ran her kitchen faucet while the crew was working in the unit below her. It came on. She texted the owner a thumbs-up. That was the first text about water in two years that was not a complaint.

The pets, the work-from-home tenant, and the baby

Every building has them. A dog that panics at drills. A tenant on video calls all day. A newborn napping at two in the afternoon.

Tell the crew. Most of this is easy to plan around once you know. The loud work in a unit can happen on a day the tenant is out. The dog can go to a friend’s for a day. The video-call tenant may be fine working from a coffee shop for the afternoon the crew is in the wall behind their desk.

None of that is in a code book. It is just the difference between tenants who renew and tenants who leave a review.

What gets opened, and what gets patched

Owners picture the walls coming down. That is not what a repipe looks like.

The crew opens access holes where the new pipe has to pass through, connect, or turn a corner. In a two-story building, that often means some openings in the ceilings of the downstairs units to reach pipe for the upstairs units, and some openings in walls behind sinks, toilets, tubs, and the laundry. In a building with a crawlspace, a lot of the horizontal runs can happen underneath, which keeps the wall openings smaller.

Then the openings get patched. Ask in the scope who patches, to what level, and who paints. Some owners like to have their own painter do the final coat so the colors match their turnover paint. Either way, write it down before anyone picks up a tool.

Here is a small thing that helps in a rental. Ask where the new pipe will run and take photos before the walls close. When you remodel a kitchen in ten years, you will know where the water is. Your future self will think you were very organized.

PEX or copper in a rental building

We install two materials. Uponor PEX-A, with a 25-year parts and labor warranty. Or L-grade American copper, with a 30-year warranty. Copper on the same scope costs more.

For a rental, the choice usually comes down to two questions.

  • How long are you keeping the building? Both warranties run longer than most owners plan to hold a building. If you are passing it on to your kids, the way this owner’s father passed it to her, the longer copper warranty may matter to you.
  • How much wall do you want open? PEX-A is flexible and can often be snaked through spaces with fewer openings. Copper is rigid and is joined at each turn. On the same building, that can mean different access.

Neither one is the wrong answer. The owner in Santa Clara picked PEX-A. She said the 25-year warranty was longer than she planned to be anybody’s landlord.

The water heaters, the stops, and the main shutoff

A whole-building repipe touches more than the pipe in the walls. Here is what we look at in a small building, and what you should ask about in any scope.

  • The main shutoff. Where it is, whether it actually closes, and whether you can reach it without lying in a flower bed. In Santa Clara the old valve was a gate valve that took eleven turns and still let water by. The new one is a quarter-turn valve in a spot you can reach standing up.
  • The unit shutoffs. One per unit where the layout allows. This is the change tenants notice most.
  • The fixture stops. The small valves under each sink and behind each toilet. Old ones seize or snap when you finally need them. New quarter-turn stops at every fixture are a normal part of a repipe.
  • The water heater connections. The new pipe ties into each water heater. If a heater is near the end of its life, that is worth knowing now, so you are not opening the same closet twice. A water heater replacement is its own job, with its own scope.

Ask for every one of those to be written into the scope, unit by unit. “Repipe building” on an estimate is not a scope. “New main from the meter side to the building, branches to Units A through D, unit shutoffs at each, new stops at each fixture, connections at four water heaters” is a scope.

What a repipe does not cover

A water-supply repipe replaces the pipe that brings clean water to your fixtures. It does not replace the drains, the sewer line, or the gas line. Those are separate systems with separate pipe.

We mention this because in a building the age of the Santa Clara fourplex, all of those are old. An owner who just got through a supply repipe sometimes assumes the slow drain in Unit B is next on the same list. It might be. It is a different scope, and it should be looked at on its own.

One service per job, written clearly. That is how you know what you paid for.

The permit, and the paper you keep

On a repipe, the permit gets pulled before the work starts. The city inspector looks at the new pipe, and the job gets a final. We pull the permit on a whole-house water-supply repipe, and a building repipe is that same work, times the number of units.

Here is the paper a building owner should end up with.

  • The contractor’s license number. Ours is CSLB #1057926. Check any contractor’s number on the CSLB website before you sign.
  • The permit and the final inspection. Keep a copy with the building records. If you ever sell, refinance, or get asked by an insurance company, it is the first thing they want.
  • The material and the warranty. PEX-A or copper, and the warranty in writing.
  • The scope. What was replaced, unit by unit, including valves and stops.
  • Photos of the open walls. Not required. Very useful later.

Her father’s shoebox is still on a shelf in her office. The repipe paperwork went in a folder. Small victories.

What the owner learned about the tenants

Owners worry that a repipe will make tenants angry. In our experience, the thing that makes tenants angry is not the repipe. It is surprises.

A tenant who gets a clear letter, a schedule, and a phone number usually handles a few days of dust and some daytime shutoffs just fine. A tenant who comes home to a hole in the ceiling with no warning does not.

In Santa Clara, the long-term tenant in Unit A, the one who had been there for decades, told the owner something on the last day. She had been worried for years about the pipes. She just did not want to be the tenant who complained. The repipe was the first thing in a long time that made her feel like somebody was taking care of the building.

That is not a plumbing fact. It is still worth knowing.

A few questions to ask before you sign anything

Whether you hire us or someone else, these are worth asking on any small-building repipe.

  • Is the scope written unit by unit, including the main and the shutoffs?
  • Who pulls the permit, and is the final inspection included?
  • What is the shutoff plan? Which days, roughly what hours, and is water back on each evening?
  • Will each unit get its own shutoff where the layout allows?
  • Who patches the openings, and who paints?
  • What material, and what warranty, in writing?
  • How will the crew handle tenants, pets, and keys?

If the answer to any of those is a shrug, keep asking.

What happened in Santa Clara

The owner sent her letter. The 24-hour notices went out unit by unit. The permit was pulled before anyone opened a wall.

The crew started with the main and the unit shutoffs. After that, they worked through the units, one at a time. Water went off during working hours and came back on in the evening. The tenant with the dog dropped him at her sister’s on the day the crew was in her unit. The tenant on video calls worked from the library.

The city inspector came out, looked at the new pipe, and signed off. The walls got patched. The owner’s painter matched the turnover paint.

Three weeks later, at 6:40 on a Sunday morning, the owner’s phone buzzed. It was the tenant in Unit C. It was a photo of a pancake. The caption said, “Water pressure is ridiculous now. Thank you.”

She has kept that one.

If your building has one valve and four tenants

Do not wait for the Sunday morning text. Go back through your tenants’ messages and look for the quiet signs: weak pressure, brown water, a shower that goes cold. Get the whole building walked by someone who repipes buildings. Then pick between patching, one unit, and the building with a real scope in your hand.

Book online, or call (408) 295-4309. Repipe Champions, CSLB #1057926. Free estimates.

Talk to Repipe Champions

★★★★★5.0 on Google · 116 reviewsRead reviews
★★★★★

“Gil’s crew ripped the old pipe out in one day. Patched the holes, swept up, water’s clear now. I was sure something would be leftover. Nope. I am very pleased!”

Bre M. · Google review · Sep 2026
★★★★★

“Travis did the copper. Inspector passed it the first time around! Done! The crew was very helpful and understanding when it came to my questions.”

KUNA L. · Google review · Sep 2026
★★★★★

“The pipe replacement was finished in one day. The crew was experienced, professional, and left everything clean when they were done. We were very happy with the work.”

Elvis · Google review · Jun 2026
  • CSLB #1057926
  • Licensed & insured
  • Uponor certified installer
  • PEX-A 25-yr / copper 30-yr warranty
  • Permits pulled & inspected
  • Free estimates
  • 0% APR financing
About the author
Gil Geva, Owner of Repipe Champions. CSLB-licensed contractor (B + C-36, #1057926). Bay Area repipe specialist.

Similar Posts

Our Crew in Action

Licensed repipe specialists serving the Bay Area

Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work Repipe Champions crew at work